The Ohio State University

Sr. Research Engineer


BSc 1993, The Ohio State University
MSc 1995, The Ohio State University

Room E328
201 W. 19th Ave.
Columbus, OH 43210

Research:

Assistant Director of the GearLab - Gear and Power Transmission Research Laboratory under Dr. Ahmet Kahraman (Director) and Dr. Donald R. Houser (Founder). Focus on gear design, noise, analysis, and optimization.

Selected Publications:

1. D. R. Houser and J. Harianto, "A Methodology for Obtaining Optimum Gear Tooth Micro-Topographies for Noise and Stress Minimization over a Broad Operating Torque Range," DETC2007-34655, The 10th ASME International Power Transmission and Gearing Conference (PTG), Las Vegas, NV, September 2007.
2. D. R. Houser, S. Shon, and J. Harianto, ""An Evaluation of FZG Micro-pitting Test Procedures and Results for the Crowned AGMA Test Gears," American Gear Manufacturing Association (AGMA) Technical Paper, Orlando, FL, October 2006.
3. D. R. Houser and J. Harianto, "The Effect of Micro-Geometry and Load on Helical Gear Noise Excitations," Proceedings of the 2005 Noise and Vibration Conference (2005-01-2295), SAE Technical Paper, Traverse City, MI, May 2005.
4. D. R. Houser and J. Harianto, "Effect of Profile Relied on the Noise Excitations of Helical Gear," Gear Solutions magazine, March 2005.
5. D. R. Houser, S. Chang and J. Harianto, "Tooth Flank Corrections of Wide Face Width Helical Gears that Account for Shaft Deflections," DETC2003/PTG-48072, The American Society of Mechanical Engineers (ASME) and American Gear Manufacturing Association (AGMA), 2003 ASME/AGMA International Power Transmission and Gearing Conference, Chicago, IL, September 2003. This paper is also published in the Gear Technology magazine (The Journal of Gear Manufacturing), January/February 2005 issue.
6. D. R. Houser and J. Harianto, "A Gear Design Optimization Procedure that Provides Minimum Stress and Minimum Noise Gear Pair that has a Low Sensitivity to Manufacturing Error ," American Gear Manufacturing Association (AGMA) Technical Paper, St. Louis, MO, October 2002.
7. D. R. Houser, J. Harianto, J. Sorenson, H. Wijaya and S. Merugu, "Comparison of Analytical Predictions with Dynamic Noise and Vibration Measurements for a Simple Idler Gearbox," International Conference on Gears, Munich, GERMANY, March 2002.
8. D. R. Houser, H. Wijaya and J. Harianto, "The Effect of Spacing Errors and Runout on Transverse Load Sharing and Dynamic Factor of Spur and Helical Gears," American Gear Manufacturing Association (AGMA) Technical Paper (01FTM8, ISBN: 1-55589-787-8), Detroit, MI, October 2001.
9. D. R. Houser, J. Harianto and Y. Ueda, "The Effect of Manufacturing Errors on Gear Design Metrics using a Robustness Scheme," Japan Society of Mechanical Engineers (JSME) International Conference, November 15-17. 2001, Fukuoka, JAPAN.
10. D. R. Houser and J. Harianto, "Design Robustness and Its Effect on Transmission Error and Other Design Parameters," The International Conference on Mechanical Transmissions (ICMT,2001), April 5-9, 2001, Chongqing, CHINA. This paper is also published in the Gear Technology magazine (The Journal of Gear Manufacturing), March/ April 2003 issue.

614-688-3952

Email: harianto.1